Projectfinder

Situated in the City of London's Square Mile and built around and above Liverpool Street Station, MAX FRANK supplied to the new '5 Broadgate' office estate.

"Ad Fontes Musica" is a new building of three city villas in Leipzig. Involving the use of formwork elements and shear force dowels.

The water-deflecting Zemdrain^® CPF liner is being used to create the pore-free concrete surface of the Al Garhoud Bridge in Dubai.

At a cost of USD 3.0 billion the Jaber Causeway project is one of the largest infrastructure ventures in the Gulf Cooperation Council (GCC) region.

The Allmend Tunnel has already been in operation for 46 years and showed various structural damages. With the renovation of the motorway section Thun-Nord - Thun-Süd, the tunnel will also be renovated.

MAX FRANK’s patterned Insitex^® formwork liner, 'Wicklow' design, was selected by Perth & Kinross Council to finish miles of concrete river wall.

With the Alnatura working world, an architectural milestone has been reached in terms of sustainability, material efficiency, openness and modern working methods arose.

A daycare centre for 370 children has been built on the factory site of the "Alte Baumwolle" in Flöha. Saxony's largest daycare centre opened at the end of 2013.

Amazon is investing in a new logistics centre near Barcelona. MAX FRANK is supplying its largest Egcodorn^® WQ 350 shear force dowel for the project.

MAX FRANK supplied Stremaform^® Strong permanent formwork, for deep slabs & bases to this redevelopment project.

The "Aquis Plaza" shopping centre was built in the shopping street Adalbertstraße in the centre of Aachen. It was opened in the autumn of 2015.

Insitex^® architectural formliners were chosen for use on an Environment Agency flood prevention scheme in the town of Whitworth in the Rossendale Valley, Lancashire.

Pecafil^® permanent formwork (Type VR6) was successfully used in the groundworks of the new stands of the Ashton Gate Stadium.

MAX FRANK Spain planned the waterproofing concept for the reinforced concrete tank of the 'Atlantis Aquarium' leisure centre in Madrid.

The Stremaform^® sound insulation joint was used as a formwork element and provides the necessary sound decoupling between the buildings of the Aubach villas.

The new August-Kühne-Haus is currently under construction at the historic headquarters of the logistics company Kühne + Nagel in Bremen. MAX FRANK supplied thermally insulating Egcobox^® cantilever connectors for the precast sections of the load-bearing exposed concrete façade.

Situated centrally in Bavaria, Ingolstadt Station is an important hub in the Deutsche Bahn AG railway network.

In December 2011 the construction of the multi-storey railway station "Łódź Fabryczna" in Poland started.

As part of the “Stuttgart 21” transport infrastructure project, Stuttgart’s existing main railway station is being converted into an underground through-station flooded with light. For the chalice-shaped pillars on the future railway platforms, MAX FRANK is supplying fibre-reinforced concrete single spacers.

One of the largest urban building projects in Australia, with high-rise buildings and a financial district, is being built in Barangaroo, Sydney.

The BAYSIDE Hotel opened in 2014 in Scharbeutz on the Baltic Sea coast. The Egcotritt stair landing bearings ensure the soundproofed connection of the balcony slab.

For the Beuth University of Applied Sciences in Berlin, the concrete letters of the "BEUTH HOCHSCHULE FÜR TECHNIK" lettering were created using Fratec^® forming formwork.

BMW Welt is a museum, exhibition and event centre which celebrates the BMW brand and is located close to the Vierzylinder tower in Munich.

Bond Street, in the heart of London's West End, is the busiest shopping district in the UK.

Developer Crest Nicholson announced the launch of Mandeville Place, a collection of apartments and family homes in Brampton, Cambridgeshire.

Below the Brenner Pass the world's longest underground rail link for goods and passenger traffic is being built.

The combination of Sorp 10^® room-acoustic sound absorber and Sorp acoustic plaster meets the acoustic and optical requirements.

The "Business Garden Bucharest" office and commercial premises are situated in a central location in the capital city, surrounded by spacious gardens.

The Casa da Música is the municipal concert hall in the Portuguese city of Porto. The concert hall was designed with exposed concrete surfaces inside and out.

An optimum room acoustics for 500 office workplaces was achieved with Sorp 10^®, the sound absorber for thermally activated components.

Two new tunnels are being built in the Stuttgart Europaviertel. A mass-spring system with the Egcodorn^® DND is being used for the purpose of acoustic decoupling.

The construction of the Citygate project in Vienna began in 2013. It will include a shopping centre with 20,000 sqm of retail space and around 1,000 apartments.

CityLife in Milan is to be a new business and residential district. Its landmarks include the three towers Torre Isozaki, Torre Hadid and Torre Libeskind.

For the Clem Jones Tunnel project in Australia, MAX FRANK supplied fibre-reinforced concrete spacers as well as the Intec^® injection hose system for joint seal.

For the crane runway foundation of the container terminal in Glauchau, shear force dowels of the type Egcodorn^® DND were used for dynamic loads.

Egcodorn^® DND 350 shear force dowels were used for dynamically stressed joints in the crane runway at the Rostock terminal.

The Pecafil^® universal formwork elements were used for the complicated foundations of the day care centre in Haseldorn.

The Donau City Tower in Vienna is currently the tallest building in Austria. The new landmark with its characteristic "crystal façade" is highly impressive.

Exposed fibre-reinforced concrete cones form a design element in the construction company Dechant's new administration building.

The Egcovoid^® void former was installed in the pension insurance firm's administration building to achieve load activation of the underground car park ceiling.

MAX FRANK supplied Stremaform^® permanent formwork for construction joints, assembled on the seabed, for the extension of the "Muelle Poniente Norte" dock in the harbour of Palma de Mallorca.

Zemdrain^® CPF liner was used for a low-pore surface of the concrete walls in the Essen water treatment plant.

The internal walls of the water storage tank were lined with the Zemdrain^® CPF liner. The use of Zemdrain^® increases the service life of the concrete surface.

Dubai Frame opened in January 2018 offers visitors an observation platform and a museum.

In September 2011 a new shopping center with an area of ​​43,000 m² was opened in Szczecin.

In the new elevated tank in Höchsten, Dortmund the service life of the concrete has been provably increased with the water-deflecting Zemdrain^® CPF liner.

Approx. 700 Egcotritt light shear force dowels have been installed for sound decoupling between the lift shaft and ceilings in the Eurogate passive house residential complex

To ensure compliance of the concrete cover in the Exzenterhaus, a range of fibre-reinforced concrete spacers in various designs have been installed.

This modern commercial project comprises a mixed use development of office and sub-divisible retail space in the centre of the City of London.

With 39 floors the 218-meter-high Intesa Sanpaolo tower in Turin is the headquarters of the largest Italian credit institution.

Fish Island is located south of the Hertford Union canal and is a new, mixed-use development in Hackney Wick, London.

A new weir has been built for the flood protection of the city of Forst. The Zemdrain^® CPF liner will improve the concrete quality in the long term.

MAX FRANK Spain supplied more than 9,000 sq.m. Pecafil^® permanent formwork for pile head foundations to expansion of the airport in Santiago de Chile.

MAX FRANK Tubbox^® "blowhole-free" column formers were used for the round columns for the bus station. The Zemdrain^® CPF liner, placed inside the Tubbox^® column formers, ensures a blowhole-free concrete surface.

An exclusive collection of penthouses at London Dock were recently unveiled.

Egcobox^® thermally insulated cantilevered connectors were used in the Fregata residential complex project in Gdansk (Poland).

MAX FRANK supplied Shearail^® punching shear reinforcement and Stremaform^® jointing formwork to Gallions Quarter – a multi-phase development, located in the Royal Albert Basin area of the Royal Albert Docks.

In the south of Chile, in Valdivia an eight floors building was built in January 2018, which contains shops, restaurants, offices and flats.

MAX FRANK supplied Shearail^® to combat 'punching shear' on this new, mixed-use residential development.

Complex reinforcement work in the area of expansion joints was avoided by use of the Egcodorn^® shear force dowel in the Gustav-Heinemann Quarter.

For the walls of the weir, MAX FRANK AG Bösingen supplied coloured sealing cones and fibre-reinforced concrete single spacers.

The Stremaform^® formwork element was installed in the working joints for Lehrter Station in Berlin.

Tubbox^® column formers were used for the round concrete columns at the south-east entrance to the new Breslauer Platz/Hauptbahnhof underground station.

Shaping formwork Fratec^® was used to realise a decorative ceiling at the "house of religions" in Bern.

A modern, purpose-built care home has been developed for long term nursing care for general needs as well as specialist dementia care.

After more than 60 years, Heathrow’s Terminal 2 building will be replaced with a new terminal which will eventually become the home of Star Alliance.

Complex formwork around the expansion joints was avoided by using Egcodorn^® shear force dowels.

Max Frank Ltd. supplied Pecafil^® permanent formwork, plastic side spacers and fibre concrete triangular base spacers to the groundworks of Hilton Garden Inn.

MAX FRANK Spain supplied the Egcobox^® thermal break balcony connector for the project.

The modern luxury hotel Arka Medical Spa in Kolberg, Poland, was built in 2012.

Requirements for the balcony types at the four-star Hotel Carat could only be solved with custom versions of the Egcobox^® cantilever connectors.

Pecavoid^® cellular void former was selected as an effective solution to combat slag heave during the construction of a new Anaerobic Digestion (AD) Plant.

Located in Stoke Newington, The Kings Crescent Estate is a large scale regeneration project consisting of 273 new build properties.

In October 2015 Berkeley Homes obtained planning permission to redevelop the former Kingston Gas Works site.

MAX FRANK Spain has supplied sealing products for a wastewater treatment plant in Andratx.

The treatment plant Waßmannsdorf will be enlarged to catch the rising wastewater volume in the district Dahme-Spreewald. Two additional purification tanks and a mixing water storage will result.

At a filling station in Bratislava Tubbox^® column formers, type "spiral“ were used for the formwork of the concrete circular columns.

FRANK distance tubes and sealing cones were used for the exposed concrete surfaces of the Museum Island Hombroich.

Liebherr-Logistics GmbH is building a logistics centre and an administration building for the IT department in Kirchdorf.

A new university campus, overlooking the sea, will be created in the city centre of Kalmar.

Pecavoid^® ground heave solution & Egcobox^® thermal breaks were supplied to this purpose-built, mixed-use development.

The Main Point Karlin administrative building was nominated "Office building with high level of technology and sustainable architecture".

Around 600 concrete columns were produced with the reusable Tubbox^® Multi circular column formers for the "Mathematikon" in Heidelberg.

Aspects of sustainability and durability were planning objectives from the start and were realised with Sorp 10^®.

Italy’s "MAXXI" National Museum for Arts of the 21st Century was designed by the architect Zaha Hadid. The museum was opened in Rome in 2010.

A new laboratory building is being built at the TU Chemnitz. The base plate required a targeted introduction of the building loads as well as high tightness against radon.

The Mersey Gateway will bring about much needed traffic relief for the existing congested and aging Silver Jubilee Bridge.

In 2015 the first minaret was built in Stuttgart. Fratec^® forming formwork was used for the special column architecture of the minaret.

The mine water cleaning plant was the realisation of an environmental protection project for clean water. MAX FRANK supplied sealing technology products.

The MO.S.E project is a storm surge barrier currently under construction. Installed by the lagoon of Venice it is designed to protect against flooding.

The Egcotritt stair landing bearing was installed in a multi-family dwelling to prevent unwanted sound transmission in staircases.

The former New Bridewell Police Headquarters was demolished to make way for 499 beds of purpose built student accommodation and approximately 6,500 sqft of commercial floor space at ground floor level.

An industrial hall for a German automobile manufacturer is being built near Landshut. This project included the use of the 32 mm diameter Coupler position connection.

A unique concrete element of the "Neues Theater" is the "bubble façade", which was produced using Fratec^® special formwork.

In Germany's oldest still working ship lift, Stremafix^® back anchoring was used in the working joints of the reinforced concrete.

MAX FRANK supplied Shearail^® prefabricated punching shear reinforcement to the south west London District re-development.

Nová Karolina is one of the largest urban development projects in the Czech Republic. Modern apartments as well as office and commercial buildings have grown up in Ostrava.

The Austrian Automobile, Motorcycle and Touring Club (ÖAMTC) opened its 'Mobility Centre' in Vienna-Erdberg.

The Oeresund Bridge connects the Danish capital Copenhagen and Malmö in Sweden.

Design and office workplaces for creative working in an open workshop ambience.

An office complex with 20,000 sqm of rental space, 47 underground parking spaces and 37 outdoor parking spaces has been built on Nordkanalstraße in Hamburg Hammberbrook.

The "Ohligsmühle" building complex was built in Wuppertal-Elberfeld. The concrete working joints were securely sealed with Fradiflex^® metal water stop.

The "Palais an der Oper", the former Residenzpost on Munich's Maximilianstraße, has been renovated and rebuilt as an exclusive residential and commercial building.

MAX FRANK supplied Egcobox^® thermal breaks to the housing development at Peel Centre, London.

In the Playmobil logistics centre, the transmission of shear forces of slab-form components in the expansion joints is achieved by the use of Egcodubel.

The Sohlstufe Lehen power station won a category of the "European Concrete Award 2014". MAX FRANK supplied formwork elements and fibre-reinforced concrete distance tubes.

The Insitex^® Brecon profile was chosen to enhance a normally plain concrete structure.

The suspension bridge located in Vorderhein, canton Grisons enables pedestrians and cyclists to cross the Rhine.

The Q 6 Q 7 project gives the city of Mannheim a multifunctional quarter consisting of attractive retail, restaurant and office space, as well as rental apartments.

The Egcoscal stair bedding offers high-performance impact sound reduction and greatly improves the comfort of the residents of the Färberstraße Quarter.

The Queensferry Crossing is the world's longest cable-stayed bridge and Scotland's largest infrastructure project.

Tubbox^® column formers for blowhole-free circular columns were used in the construction of the concrete columns for the Lingen Technology Centre.

In the floodplain of Deggendorf, watertight seals of the sophisticated building geometries were created with the Zemseal^® sub-structure waterproofing system.

Six new residential buildings, which accommodate 30 apartment, were created near the coast in the popular area of Sandlyckan in Kullavik.

The coupling of the joints was created by Egcodorn^® shear force dowels which were integrated into a formwork element with internal and external rubber water bars.

MAX FRANK supplied Egcobox^® FST steel-to-steel thermal breaks to new residential building.

MAX FRANK supplied Shearail^® to increase construction speed & combat 'punching shear' on this redevelopment project.

The transformation of the N329 into the "road of the future" is the way ahead for road design and technology.

Sorp 10^® enables reduction of reverberation times with minimum influence on thermal component activation.

The works consisted of the construction of a new spa and hotel extension to the Grade 1 listed historic Rudding Park Hotel nestled within an 18th century Repton landscape.

In the bridge structure, the Stabox^® special rebar connection for high shear forces were able to guarantee the most demanding requirements for an "indented" working joint.

Due to the high groundwater contamination, a sealing concept with FBV system was planned as an additional measure.

The Schwabenlandtower, previously known as Gewa-Tower, is the highest residential building with 107 metres height in Baden-Württemberg.

An exposed concrete ribbed slab was produced with Fratec^® forming formwork for a sepulchral chapel in the Waldfriedhof cemetery in Munich.

Tubbox^® Multi special circular column formers were used in the circular tank of a sewage plant in the municipality of Palazzolo sull'Oglio in northern Italy.

For the thermal decoupling of the balcony slabs, over 1,650 Egcobox^® thermally insulating cantilever connectors have been installed in the SKY construction project.

The Sky Tower is a three-part high-rise building in Poland. MAX FRANK supplied Stremaform^® formwork elements for the production of the working joints.

The expansion joints were constructed with Stremaform^® formwork elements with internal expansion rubber water bar and integrated Egcodorn shear force dowels.

Smart Campus is the new headquarters of Wiener Netze GmbH. The Egcodorn^® shear force dowel was used in the expansion joints.

The Egcovoid^® void former was used in a residential resort to achieve a targeted load application in the foundation area on the sandy ground.

Void former Egcovoid^® enables the construction of a new school building onto existing structures without load transfers.

The Egcobox^® thermally insulating cantilever connector was used in the creation of a projecting solar protection structure at the State Office of Finance.

The Tamina Bridge is a road bridge in the Tamina valley in the canton of St. Gallen. The Structural Designers received the StructuralAward2018.

The permanent formwork Pecafil^® universal formwork elements was chosen for the concreting work on the individual foundations and the floor slab.

The permanent formwork Pecafil^® was supplied by MAX FRANK Spain for the foundation of a housing complex with 93 units.

The Shard is the tallest building in Western Europe.

In the center of Bucharest the project developer Vastint started a construction project, which comprises three buildings.

A new gantry crane has been built for the port. The coupling of the dynamically stressed joints is created with Egcodorn^® DND 300 shear force dowels.

MAX FRANK Spain has supplied Stremaform^® formwork elements for the construction joints of the foundation slab.

The CityLife project in Milan is characterized by three towers: "Torre Isozaki", "Torre Hadid" and "Torre Libeskind" - named after the respective architects.

MAX FRANK Spain supplied fibre concrete spacers for the production of precast concrete parts for the Quito subway tunnel. A total of 30 containers were supplied.

MAX FRANK supplied Shearail^® punching shear reinforcement system, which was adapted for use in semi-automated pre-cast production processes.

Coloured exposed concrete and coloured fibre cement cones from MAX FRANK set accents in the University of Applied Sciences in Frankfurt.

Pecafil^® universal formwork elements were used for rapid creation of the foundation formwork for the University of Economics and Business.

MAX FRANK supplied Shearail^® punching shear reinforcement & Egcobox^® thermal breaks to new accommodation building.

Achieving Visual & Durable Concrete, through the use of Zemdrain^® Controlled Permeability Formwork Liner on the V&A Project, Dundee.

The residential district Victoria Park consists of a total of 133 apartments and is located in the Limhamn district of Malmö.

The Vodafone campus includes a 19-story office tower, three building blocks and a parking garage. Bar spacers made of cast concrete were supplied for this purpose.

MAX FRANK supplied a “self-supporting” concrete jointing system, permanent formwork and sealing solutions to the largest Waste Water Treatment Works in the UK.

Insitu concrete sea walls using NOEplast were selected as an economical and durable solution to the original design of precast units with 'cast in' real-stone cladding.

MAX FRANK supplied Pecavoid^® ground heave solution to The Royal Horticultural Society's exciting new development.

In order to provide thermal insulation in the residential buildings of the settlement Szafarnia in Gdansk, thermal break balcony connectors Egcobox^® were used.

MAX FRANK supplied Stremaform^® concrete jointing system to Canary Wharf’s new district. The use of Stremaform^® enabled significant time and cost advantages to be achieved on-site.

The Z-Up residential and office complex in Stuttgart owes its name to its Z-shaped footprint.

For optimum room acoustics on the main campus, the Sorp 10^® product has been chosen as the solution for use in thermally activated components.